EXACTLY HOW TO INSTALL A BATH TUB: SET UP AN ACRYLIC TUB AND BATHTUB SURROUND

Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround

Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround

Blog Article

Book Your Appointment

This article following next on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is definitely interesting. You should investigate for yourself.


A Step-by-Step Guide to Installing a Bathtub
Setting up a tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old tub is conveniently easily accessible, the job can relocate immediately; if you have to open a wall to remove the old tub and position the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly need a helper to move out the old tub and also embeded in the new one. Ensure you have certified on your own for the task as well as are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will help you install a new bath tub in your washroom if you have actually currently gotten a new tub and don't require to transform the setup of your previous water system pipes.
Your devices as well as material checklist should make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installation


    Firstly, the sustaining framework supplied with the bath ought to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent pressure on the tub.
    Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.

    Removing Old Taps


    If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is frequently the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
    Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Tub


    Utilizing both wooden boards under its feet, put the tub in the needed position. The wooden boards are useful in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
    The following objective is to guarantee that the tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the bath tub till the level reviews degree.
    To set up faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
    Switch on the water system and also check all joints and new pipework for leaks as well as tighten them if needed. Load the tub and also check the overflow electrical outlet and the normal outlet for leakages.
    Ultimately, repair the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bath tub has actually been made use of a minimum of once as this will settle it into its last placement.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipes.
    If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former type should be attached to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bath tub


    In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to penetrate the wall in between the bath as well as the tiling, leading to issues with dampness as well as feasible leakages to the ceiling listed below.
    You can select from a selection of coloured sealants to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split relatively early if you do not take into consideration this motion prior to securing.
    Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant sticky and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I was introduced to that report about How to Install a Bathtub Yourself from an associate on our other web address. Sharing is caring. You just don't know, you may be helping someone out. I am grateful for your time. Don't hesitate to check up our blog back soon.




    Estimate


    Report this page